Protecto-AutoKare
2K PU,
Solvent-based, Clear Auto Finish
►
Description
Protecto-AutoKare is a revolutionary two
component (2K) clear polyurethane system that has been developed and
perfected by our R & D department to give total protection to
automobile paint. It gives the painted automobile surface a superb,
high gloss finish that will last for several years. The paint will
also have increased protection from scratches and the harmful
effects of environmental pollution. Dull and faded looking paint on
old automobiles look rich and vibrant after application of
Protecto-AutoKare.
►
Salient Features
● HIGH SCRATCH
RESISTANCE
Protecto-AutoKare gives a
hard, tough, scratch & wear resistant layer which protects the paint
surface.
● FAST DRYING
Protecto-AutoKare is
extremely fast drying and dries within 10 to 15 minutes. This
prevents dust from settling down on it and spoiling the finish.
● SUPERB
FINISH
Protecto-AutoKare
enhances the beauty of the paint and gives it a rich glossy look.
● EXCELLENT
WATER AND CHEMICAL RESISTANCE
Protecto-AutoKare prevents
the paint from being damaged due to exposure to water. It also shows
excellent resistance to many dilute acids, alkalies and oils.
● HIGH STAIN
RESISTANCE
Protecto-AutoKare does
not get stained by dirt, oil and mud and retains its gloss for a
long period.
● HIGH HEAT, WEATHER
& UV RESISTANCE
Protecto-AutoKare has
excellent resistance to heat and is not affected by changes in
weather conditions. It has unmatched UV resistance.
● LONG LIFE
Protecto-AutoKare preserves
the paint and keeps it looking fresh and vibrant for several years.
►
Application
Protecto-AutoKare is a two
pack system in which both components are mixed thoroughly before
applying. Mixing ratio is 1:4 by volume. Add any suitable thinner
such as ‘ProtectoCoat – Thinner102’ to
bring the viscosity down. Apply two / three coats of
Protecto-AutoKare
by spraying (at 1.8 kg/sq. cm. pressure) keeping a gap of around 4
-5 hours between coats. Allow the final coat to dry thoroughly.
Full scratch hardness is achieved after 4 days.
Spirit or alcoholic
solvents should not be used as thinners for Protecto-AutoKare. We recommend
‘ProtectoCoat - Thinner 102’ if
you wish to thin Protecto-AutoKare.
To avoid
whiteness and dull appearance of coatings, ensure that the
compressor is drained completely and the compressed air is free of
moisture.
►
Properties
Coverage
|
9-10 sq.m/litre
(m2/L) |
Mixing Ratio |
1 : 4 by
volume |
Pot life
(25°C) |
2-3 hours |
Tack free
time (25°C) |
10 to 15
minutes |
Scratch
hardness |
2000 gms
|
Recoatability |
After 4-5
hours |
►
Storage and Precautions
Protecto-AutoKare should be stored in a
cool, dry and spark free area. It can be stored for 6 months in its
original, unopened container. As far as possible, all the material
from the container should be used up once the container is opened.
To store unused Protecto-AutoKare, transfer it to a small airtight and
impurity-free container
leaving no air gap on top. While handling, all contact with eyes,
skin, and clothes should be avoided. Implements used for application
of Protecto-AutoKare should be cleaned with
‘ProtectoCoating -
Thinner 102’ or NC thinner.
Protecto-AutoKare
formulations are subject to strict quality control, innovations
and improvements to comply with our high standards.
The above information is given on
the basis of our best knowledge and information and is for your
guidance only.
Specifications, however, are
subject to change and no guarantee is given or implied. All
Rights Reserved.
Last Updated - April 2013
DEVELOPED & MANUFACTURED BY:
Industrial Products Mfg. Co.
|
108/109 Parmar Chambers,
3/4 B. J. Road, Pune 411001 INDIA
Tel: 91-20-26129521, 26122612
Fax: 91-20-26124362
E-mail: Contact@IPMCIndia.com
www.IPMCIndia.com
www.ProtectoCoatings.com
|
All
Rights Reserved. 1980 - 2014
|