Home

About Us

Roof

Coatings

Wood

Coatings

Floor

Coatings

Wall

Coatings

Glass

Coatings

Anti-Corrosion

Coatings

Customer List

Contact Us

                   

 

 

 

Surface Protection Solutions

    

 

 

 

 

 

 

 

 

 

 

 

 

 

     

 

     

  

Manufacturer of advanced polyurethane based systems for residential, commercial and industrial markets!

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Protecto-Ezefil 600/700

 

Expanding Type Polyurethane Chemical Grout

 

  

 

DESCRIPTION:

 

Protecto-Ezefil 600/700 is a two component, expanding type, solvent free polyurethane liquid chemical grouting material which is injected into cracks and voids to immediately stop water infiltration. The material is fast setting and reacts specifically under wet conditions to expand to several times its original volume.

 

SALIENT FEATURES:

  • High volume expansion

  • Low Viscosity

  • Permanently flexible

  • Good adhesion to wet and dry surfaces

  • Withstands high hydrostatic pressure

  • Easy to apply

  • Environmentally safe (cured product is inert)

  • Impermeable to water

  • Bridges wide gaps

  • Economical

USES:

 

Protecto-Ezefil 600/700 permanently stops water which is infiltrating through:

  • Cracked or honey - combed concrete slabs

  • Tunnels and dams

  • Joints in concrete / rocks

  • Canals

  • Waste water tanks

  • Sewers, manholes and utility boxes

  • Pipe intrusions

  • Basements

  • Voids in pre-fabricated members

   

APPLICATION:

 

Remove all dirt, grease and loose particles from the crack, Crack should be clean and sound. Drill holes of 12 mm and above along the side of the crack at a 45° angle. The hole should intersect the crack midway through the substrate. Fix injection nipples in the holes. If the concrete does not have sufficient moisture to activate the grout then inject a small quantity of water into the crack prior to injecting the chemical grout. Mix  Protecto-Ezefil 600 and Protecto-Ezefil 700  in a 20 :1 ratio by volume (i.e. mix 20 parts of Protecto-Ezefil 600 with 1 parts of Protecto-Ezefil 700). Pump the mixture into the crack at a pressure much higher than the water pressure to ensure that the water is pushed back and displaced by the injected material.

 

Pump the material for one minute and then pause to allow the material to flow into all the voids. Watch for flow of material and movement of water at the surface. When movement stops, inject into the next crack. For vertical crack sealing, start injecting at the bottom of the crack and then move upwards. Re-inject, if required, to ensure that all void and sealed off. Best results are obtained when substrate temperature is greater than 5°C and material temperature is above 15°C. Clean the pump by flushing with  xylene, toluene or N.C. thinner.

 

TECHNICAL DATA:

 

Specific Gravity

1.1 ± 0.05

Colour

Brownish

Viscosity at 20°C

2 poise

Mixing Ratio

Protecto-Ezefil 600 : Protecto-Ezefil 700 = 20:1 by volume  

Volume expansion

500-600%

Cream Time

1-2 minutes

Shelf Life

6 months in unopened containers

        

STORAGE AND  PRECAUTIONS:

 

Protecto-Ezefil should be stored in a cool and dry area. It can be stored for 6 months in its original unopened container. Material from tin cans should be completely used up immediately after opening the can. Protecto-Ezefil  may cause irritation to eyes, skin and the mucous membrane; and is harmful if swallowed. While handling, all contact with eyes, skin and clothes should be avoided.

 


All Protecto-Ezefil formulations are subject to strict quality control, innovations and improvements.

The above information is given on the basis of our best knowledge and information and is for your guidance only.

Specifications, however, are subject to change and no guarantee is given or implied.

Last Updated - April 2013


 

 

DEVELOPED & MANUFACTURED BY:

Industrial Products Mfg. Co.

 

108/109 Parmar Chambers,

3/4 B. J. Road, Pune 411001 INDIA

Tel:  91-20-26129521, 26122612

Fax: 91-20-26124362

E-mail: Contact@IPMCIndia.com

www.IPMCIndia.com

www.ProtectoCoatings.com

 

 

 

All Rights Reserved. 1980 - 2015

 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Industrial Products Mfg. Company 108-109 Parmar Chambers, 3/4 B. J. Road, Pune 411001 India

www.IPMCIndia.com   ●   Tel: 91-020-26129521  ●   Fax: 91-20-26124362

Since 1981